diff --git a/docs/guides/postinstall.md b/docs/guides/postinstall.md
index 1c2d3916..5476c5e9 100644
--- a/docs/guides/postinstall.md
+++ b/docs/guides/postinstall.md
@@ -98,6 +98,43 @@ The steps to be followed vary depending upon the initramfs module loading mechan
 
     In this case, refer to its documentation and ensure `t2bce_dma`, `t2bce_core`, and `t2bce_vhci` are loaded early.
 
+## Booting from a Thunderbolt drive
+
+Thunderbolt devices must be authorized before Linux can use them (the security level is `user`). After boot, `bolt` takes care of this, for example:
+
+```sh
+boltctl list
+boltctl enroll --policy auto <UUID>
+```
+
+If the root filesystem is on a Thunderbolt drive, the drive must already be authorized inside the initramfs, where `boltd` is not running. Otherwise the drive never shows up and boot stops at the `(initramfs)` prompt. As a one-off workaround, you can authorize it from that prompt and continue booting:
+
+```sh
+ls /sys/bus/thunderbolt/devices/            # the drive is the device whose name does not end with -0, e.g. 0-3
+echo 1 > /sys/bus/thunderbolt/devices/0-3/authorized
+exit
+```
+
+To make it permanent, add a udev rule that authorizes the drive and include it in the initramfs:
+
+- On systems with `initramfs-tools` (tested on Linux Mint 22.3, which is Ubuntu-based), custom rules in `/etc/udev/rules.d/` are copied into the initramfs:
+
+    1. Find the `unique_id` of the drive with `cat /sys/bus/thunderbolt/devices/0-3/unique_id` (replace `0-3` with your device).
+
+    2. Create `/etc/udev/rules.d/99-thunderbolt-root-auth.rules` with the following content:
+
+        ```text
+        ACTION=="add", SUBSYSTEM=="thunderbolt", ATTR{unique_id}=="<unique_id of the drive>", ATTR{authorized}=="0", ATTR{authorized}="1"
+        ```
+
+    3. Run `sudo update-initramfs -u`, and check that the rule is included with `lsinitramfs /boot/initrd.img-$(uname -r) | grep thunderbolt-root-auth`.
+
+- On systems with other initramfs/initrd generation systems:
+
+    Refer to its documentation to include the udev rule in the initramfs.
+
+Note that `unique_id` is reported by the device itself, so this rule weakens the protection that Thunderbolt authorization provides.
+
 ## Adding support for customisable Touch Bar
 
 By default the Touch Bar works in the same mode which Windows Bootcamp uses on Linux. If you want to customize it, you can install `tiny-dfr` on your distro.
diff --git a/docs/state.md b/docs/state.md
index 2570e6f9..c2f48b2e 100644
--- a/docs/state.md
+++ b/docs/state.md
@@ -12,7 +12,7 @@ While Linux is usable on all T2 models, some features are limited due to the lac
 |Wi-Fi|🟢 Working|🟢 Yes|Requires macOS firmware|[Setup guide](https://wiki.t2linux.org/guides/wifi-bluetooth/)|
 |Bluetooth|🟡 Partially working|🟢 Yes|Requires macOS firmware only for devices with BCM4377 chip. Also, Bluetooth glitches on devices with BCM4377 Chip if connected to a 2.4 GHz Wi-Fi connection. Thus, in order to use Bluetooth either turn off your Wi-Fi or use a 5 GHz Wi-Fi connection.|[Setup guide](https://wiki.t2linux.org/guides/wifi-bluetooth/)|
 |Camera|🟢 Working|🔴 No||[t2bce](https://github.com/deqrocks/t2bce)|
-|Thunderbolt|🟢 Working|🟢 Yes|If it doesn't work, try adding `pcie_ports=native` in the kernel parameters via GRUB.||
+|Thunderbolt|🟢 Working|🟢 Yes|If it doesn't work, try adding `pcie_ports=native` in the kernel parameters via GRUB. Connected devices must be authorized before use, e.g. with `boltctl`. To boot from a Thunderbolt drive, see [Booting from a Thunderbolt drive](https://wiki.t2linux.org/guides/postinstall/#booting-from-a-thunderbolt-drive).||
 |Touch Bar|🟢 Working|🟡 Partial|"Touch Bar Keyboard" mode works OOTB, where only the Function Keys or the Media/Brightness Control Keys are shown. Touch Bar drivers were upstreamed in kernel 6.15, while the internal USB connection is provided by t2bce.|[t2bce](https://github.com/deqrocks/t2bce), [tiny-dfr](https://github.com/AsahiLinux/tiny-dfr)|
 |Suspend|🟡 Partially working|🟢 Yes|t2bce handles suspend and resume of the BCE, VHCI, and audio stack. Remaining suspend issues are model-dependent and may involve other hardware.|[#53](https://github.com/t2linux/T2-Ubuntu-Kernel/issues/53)|
 |Audio|🟢 Working|🔴 No|The internal microphone has low input volume without DSP. This is a hardware characteristic and cannot be compensated for in an upstream kernel driver.|[t2bce](https://github.com/deqrocks/t2bce)|