Skip to content

About

A camera remote unlike any other: a one-button, long-range LoRa shutter remote for Fujifilm cameras. Open firmware, printable case, full build guide.

Topics

Resources

Stars

11 stars

Watchers

0 watching

Forks

Latest commit

 

History

5 Commits

Folders and files

Repository files navigation

SLR Remote: the handheld and the camera unit

A camera remote unlike any other camera remote. One that works for miles.

Picture the camera on a tripod at the edge of the lake and you two fields away with one button in your hand. You press it, and the shutter fires.

SLR Remote (SLR stands for Super Long Range) is a pocket shutter release for Fujifilm cameras that reaches far beyond any Bluetooth or infrared remote. There is no cable to the camera, no phone and no app. Half-press holds focus, a tap takes the picture, and the little screen tells you the camera got the message.

I built it because I wanted one, and you can build one too. By Aaron Phull (iinde).

What SLR Remote does

What it is

Two small units. The handheld lives in your pocket: one shoot button, a small OLED screen, an antenna. The camera unit stays with the camera, on the tripod, in the bag underneath it, or tucked beside it in a hide.

The handheld talks to the camera unit over LoRa, the long range radio used for links of several miles in open country. The camera unit then presses the shutter over Bluetooth, using the camera's own built-in remote release, the same one Fujifilm's phone app uses. The camera thinks a remote a few inches away is asking it to shoot. It has no idea you are on the far side of the valley.

Nothing plugs into the camera and nothing needs a signal, a network or an account. Switch both on, and the one button does the rest.

How it works

From button press to shutter and back

Press the button and the handheld sends a short signed radio message. The camera unit hears it, presses the shutter over Bluetooth, and sends word back, so the handheld shows PRESSED about as fast as you can look down at it.

Every hop in detail is in docs/data-flow.md. The radio link, pairing and safety behaviour are in docs/how-it-works.md.

Gallery

Handheld and camera unit together The handheld
The pair: handheld and camera unit The handheld, with its knurled shoot button
Side view Both units from above
The rolled back edge and the grip band across the seam Both units from above

What the screen shows, from ready to pressed

Exploded view of one unit: case halves, buttons, board, battery and screws
What goes inside each one

On a shoot

Wildlife from a hide, or no hide at all

Set the camera low by the feeder or the fox run, pre-focus, and walk away. The LoRa link gets through hedges, walls and car doors: on my first walk test the camera unit was shut inside a parked car and the remote was still firing it about 90 metres away with no line of sight.

Self-portraits and group shots from far off

Frame the whole hillside with you as a small figure in it. Hold the button to focus, let go to shoot. For the family photo, the timer mode gives you a countdown on the screen so you can get the remote out of sight.

Long exposures

Hands off the camera, so nothing shakes. Fire a long shutter speed with a tap from any distance. Or, with the handheld beside the camera, use bulb mode to open the shutter for anything from 30 seconds to 30 minutes and watch the clock count up on the handheld.

Time-lapse

Interval mode takes a frame every few seconds, for a set number of frames or until you stop it. Before it starts it shows you how long the run will take and what the battery has in it.

Video

Switch the camera to movie mode and the same button becomes record: one press starts the take, another stops it. Good for filming yourself when the camera is a long walk away.

A camera left where you cannot stand

Beside the track, over the water, up on the scaffold, behind the goal. Put the camera unit with it and shoot from somewhere safe and comfortable.

What it does

The mode card on the handheld

The modes, as they appear on the handheld:

Mode On a shoot
SHOT Tap for a photo: focus, a short pause, shutter. Or hold the button for a half-press, wait for focus, and let go to shoot.
AF LOCK Tap to lock focus for 10, 30 or 60 seconds (30 by default). Tap again and it fires at once, with no focus delay.
TIMER A self-timer on the remote, 2 to 20 seconds from the handheld, with a big countdown. Any press stops it.
INTERVAL A frame every 2 to 60 seconds, for 10 to 360 frames or until you stop it.
BURST Holds the shutter down for a set time, half a second to three seconds, so the camera rattles off a sequence in continuous drive. (Direct mode: handheld straight to the camera.)
BULB Opens the shutter and closes it at the time you set, 30 seconds to 30 minutes. Any press closes it early. (Direct mode: handheld straight to the camera.)
VIDEO One press to start recording, one to stop, with a running clock on the screen.

It ships showing SHOT, AF LOCK, TIMER and INTERVAL. Set "Modes shown" to "All" in the setup menu to add the rest.

One button drives everything. A tap shoots, a hold is a half-press, and a longer hold opens the mode card. If you would rather have a real two-stage shutter switch, or a second button for the menu, the firmware supports both.

The link looks after itself. Close in, it runs fast. As you walk away it shifts to a slower, longer reaching setting and the screen changes from FAST to SLOW. Walk back and it speeds up again. If the two units lose each other, they find each other again without you touching anything.

It keeps itself legal on the air too. Tell it once where you are, EU 868 for the UK and EU or US 915 for the United States, and it uses the right band and keeps to that band's rules from then on.

A few more things I am pleased with:

  • It can run on one board. In direct mode the handheld talks Bluetooth to the camera itself, which makes a tidy phone-free remote for close work. Burst and bulb run in this mode.
  • If the handheld loses power or goes out of reach while you are holding a press, the camera unit lets go of the shutter by itself. I tested it: about 10 seconds on the fast link setting.
  • The two units are paired to each other with a 6-digit code you check on both screens, and every message is signed. Nobody else's remote will fire your camera.
  • The handheld sleeps after a minute and wakes on the button. The press that wakes it takes the photo.
  • The screen shows battery for both units, signal strength, and how the last press went.
  • Add the optional GPS module to the camera unit and it can geotag your photos and share an accurate clock with the handheld. Fit a second module to the handheld as well and the screen shows the distance and compass direction back to your camera.
  • An optional tally LED on the camera unit lights when a shot fires, so the people in the group shot know when to smile.

Every gesture and every screen word is explained in docs/user-guide.md.

Build one

  1. Gather the parts: two Heltec WiFi LoRa 32 V4 boards, two LiPo cells, two antennas for your band (868 MHz in the UK and EU, 915 MHz in the US) and eight screws. The list is in docs/shopping-list.md.
  2. Print the cases and put the units together. Every part prints with no supports, and there is very little wiring. See docs/build-guide.md.
  3. Flash the same firmware onto both boards, choose which is the handheld, set your region, and pair them with each other and the camera. See docs/flashing-and-pairing.md.
  4. Go and shoot. Keep docs/user-guide.md open the first time out.

Downloads

Everything you need is on the latest release:

  • slr-remote-0.4.0-full.bin, the firmware ready to flash, straight from your browser with no tools to install. How: docs/flashing-and-pairing.md.
  • slr-remote-0.4.0-update.bin, for updating boards that already run SLR Remote, keeping their settings and pairings.
  • slr-remote-case-print-files.zip, every case part as an STL plus ready-made print plates for Bambu Studio and other 3MF slicers. No supports needed.

The same print files are in case/final/miniworks_refined/print/ if you would rather grab them one at a time.

New to all of this? Start at docs/getting-started.md. If something will not behave, try docs/troubleshooting.md and the FAQ. Read docs/safety-and-legal.md before you transmit, and always fit the antenna before you switch on.

Building in the United States? It is the same board and the same firmware. Buy 915 MHz antennas and set Region to US 915 on both boards. The US 915 setting is built to the US rules but has not been tested on air yet: I am in the UK and cannot legally transmit on 915 MHz here. If you build one in the States, tell me how it goes.

Specs

Camera Fujifilm X and GFX cameras with Bluetooth, through the standard Fujifilm remote release. Built and tested on the X-E5
Boards 2 x Heltec WiFi LoRa 32 V4 (ESP32-S3, SX1262 LoRa radio, 0.96 inch OLED)
Long range link LoRa, spreading factor 7 to 12, chosen automatically. Set Region to match where you are
Region EU 868 (UK and EU) 869.525 MHz, 125 kHz bandwidth, up to the legal limit of 27 dBm ERP, capped from the antenna gain you tell it, 10% airtime limit kept for you
Region US 915 (United States) 918.0 MHz, 500 kHz bandwidth, about 25 dBm into the antenna, no airtime limit. Built to the US rules, not yet tested on air
Response On the bench, at the fast link setting: about 180 to 225 ms from the handheld sending to the camera unit accepting the press, then about 140 ms for each Bluetooth command to the camera
Camera link Bluetooth LE (the low energy kind of Bluetooth), using the camera's built-in remote release
Pairing 6-digit code checked on both screens, every message signed
Power One LiPo cell per unit (LP603449 fits the case)
Options Quectel L76K GPS module, tally LED
Handheld 61 x 45.7 x 21.6 mm, without antenna
Camera unit 81.3 x 45.7 x 21.6 mm, without antenna
Case 8 printed pieces, no supports, 4 x M2 x 16 mm screws per unit
Firmware 0.4.0, open source, built with PlatformIO

How speed trades against reach at each link setting is in docs/range.md. What changed in each version is in the changelog. How the project got here, including the shoot button that jammed and the one that replaced it, is in docs/design-story.md.

Credits

The Bluetooth camera work builds on the open-source Furble project (MIT licence). The case is adapted from the "Meshtastic Heltec V4 Miniworks case" by Chem_Kid (Thingiverse thing 7367243, CC BY-NC). The firmware stands on RadioLib, NimBLE-Arduino, U8g2 and TinyGPSPlus.

SLR Remote is an independent home-built project, not affiliated with Fujifilm or Heltec.

The full list is in CREDITS.md.

Licence

  • Firmware: MIT. See LICENSE.
  • Case, docs and media: CC BY-NC 4.0. See LICENSE-CASE.md. The case derives from a CC BY-NC design, so it stays non-commercial: build it for yourself, keep the credit, do not sell it.

About

A camera remote unlike any other: a one-button, long-range LoRa shutter remote for Fujifilm cameras. Open firmware, printable case, full build guide.

Topics

Resources

Stars

11 stars

Watchers

0 watching

Forks

Releases

Packages

Contributors

Languages